IFM PN2292

PN-100-SEN14-MFRKG/US/ /V – Pressure sensor with display

Two switching outputs, one of them programmable as IO-Link and one as analogue output
Red/green display for clear identification of the acceptable range
The process connection can be rotated for optimum alignment
With long-term stability thanks to high overload protection
Robust design for use in harsh industrial environments

Product characteristics
Number of inputs and outputs	Number of digital outputs: 2; Number of analogue outputs: 1
Measuring range	0…100 bar0…1450 psi0…10 MPa
Process connection	threaded connection 1/4″ NPT internal thread
Application
Special feature	Gold-plated contacts
Measuring element	ceramic-capacitive pressure measuring cell
Application	for industrial applications
Media	Liquids
Conditionally suitable for	use in gases at pressures > 25 bar only on request
Medium temperature [°C]	-25…80
Min. bursting pressure	650 bar9400 psi65 MPa
Pressure rating	300 bar4350 psi30 Mpa
Vacuum resistance [mbar]	-1000
Type of pressure	relative pressure
MAWP (for applications according to CRN) [bar]	125
Electrical data
Operating voltage [V]	18…30 DC; (to SELV/PELV)
Current consumption [mA]	< 35
Min. insulation resistance [MΩ]	100; (500 V DC)
Protection class	III
Reverse polarity protection	yes
Power-on delay time [s]	0.3
Integrated watchdog	yes
Inputs / outputs
Number of inputs and outputs	Number of digital outputs: 2; Number of analogue outputs: 1
Outputs
Total number of outputs	2
Output signal	switching signal; analogue signal; IO-Link; (configurable)
Electrical design	PNP/NPN
Number of digital outputs	2
Output function	normally open / normally closed; (parameterisable)
Max. voltage drop switching output DC [V]	2
Permanent current rating of switching output DC [mA]	250
Switching frequency DC [Hz]	< 500
Number of analogue outputs	1
Analogue current output [mA]	4…20; (scalable 1:5)
Max. load [Ω]	500
Analogue voltage output [V]	0…10; (scalable 1:5)
Min. load resistance [Ω]	2000
Short-circuit protection	yes
Type of short-circuit protection	pulsed
Overload protection	yes
Measuring/setting range
Measuring range	0…100 bar0…1450 psi0…10 MPa
Analogue start point	0…80 bar0…1160 psi0…8 MPa
Analogue end point	20…100 bar290…1450 psi2…10 MPa
Factory setting / CMPT = 2
Set point SP	0.6…100 bar10…1450 psi0.06…10 MPa
Reset point rP	0.2…99.6 bar4…1444 psi0.02…9.96 MPa
Min. difference between SP and rP	0.6 bar6 psi0.06 MPa
In steps of	0.2 bar2 psi0.02 MPa
Status_B High Resolution / CMPT = 3
Set point SP	0.6…100 bar9…1450 psi0.06…10 MPa
Reset point rP	0.2…99.6 bar3…1444 psi0.02…9.96 MPa
Min. difference between SP and rP	0.5 bar6 psi0.05 MPa
In steps of	0.1 bar1 psi0.01 MPa
Accuracy / deviations
Notes on the accuracy / deviation	switch point accuracy, linearity error under DNV GL: < ± 1%: < ± 1%
Switch point accuracy [% of the span]	< ± 0,4; (Turn down 1:1)
Repeatability [% of the span]	< ± 0,1; (with temperature fluctuations < 10 K; Turn down 1:1)
Characteristics deviation [% of the span]	< ± 0,25 (BFSL) / < ± 0,5 (LS); (Turn down 1:1; BFSL = Best Fit Straight Line; LS = limit value setting)
Hysteresis deviation [% of the span]	< ± 0,1; (Turn down 1:1)
Long-term stability [% of the span]	< ± 0,05; (Turn down 1:1; per 6 months)
Temperature coefficient zero point [% of the span / 10 K]	< ± 0,2; (-0…80 °C)
Temperature coefficient span [% of the span / 10 K]	< ± 0,2; (-0…80 °C)
Response times
Response time [ms]	< 1.5
Delay time programmable dS, dr [s]	0…50
Damping process value dAP [s]	0…4
Damping for the analogue output dAA [s]	0…4
Max. response time analogue output [ms]	3
Software / programming
Parameter setting options	hysteresis / window; normally open / normally closed; switch-on/switch-off delay; Damping; Display unit; current/voltage output
Interfaces
Communication interface	IO-Link
Transmission type	COM2 (38,4 kBaud)
IO-Link revision	1.1
SDCI standard	IEC 61131-9
SIO mode	yes
Required master port type	A; (wenn PIN 2 nicht verbunden: B)
Supported DeviceIDs	Type of operationDeviceIDFactory setting / CMPT = 2471Status_B High Resolution / CMPT = 3987
Note	For further information please see the IODD PDF file under “Downloads”
Factory setting / CMPT = 2
Profiles	Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis
Min. process cycle time [ms]	2.3
IO-Link resolution pressure [bar]	0.1
IO-Link process data (cyclical)	functionbit lengthpressure14binary switching information2
IO-Link functions (acyclical)	application specific tag
Status_B High Resolution / CMPT = 3
Profiles	Smart Sensor ED2: Digital Measuring Sensor (0x000A), Identification and Diagnosis (0x4000)
Min. process cycle time [ms]	3
IO-Link resolution pressure [bar]	0.05
IO-Link process data (cyclical)	functionbit lengthpressure16device status4binary switching information2
IO-Link functions (acyclical)	application specific tag
Operating conditions
Ambient temperature [°C]	-25…80
Storage temperature [°C]	-40…100
Protection	IP 65; IP 67
Tests / approvals
EMC	DIN EN 61000-6-2DIN EN 61000-6-3
Shock resistance	DIN EN 60068-2-2750 g (11 ms)
Vibration resistance	DIN EN 60068-2-620 g (10…2000 Hz)
MTTF [years]	138
UL approval	UL Approval no.J013
Pressure Equipment Directive	Sound engineering practice; can be used for group 2 fluids; group 1 fluids on request
Mechanical data
Weight [g]	261
Materials	stainless steel (1.4404 / 316L); PBT+PC-GF30; PBT-GF20; PC
Materials (wetted parts)	stainless steel (1.4404 / 316L); AI2O3 (96%; ceramics); FKM
Min. pressure cycles	100 million
Tightening torque [Nm]	> 50
Process connection	threaded connection 1/4″ NPT internal thread
Restrictor element integrated	no (can be retrofitted)
Displays / operating elements
Display	Display unit3 x LED, green (bar, psi, MPa)switching status2 x LED, yellowmeasured valuesalphanumeric display, red/green 4-digit
Remarks
Pack quantity	1 pcs.
Electrical connection
Connection	Connector: 1 x M12; coding: A; Contacts: gold-plated
ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen — We reserve the right to make technical alterations without prior notice. — EN-GB — PN2292-01 — 21.02.2020